![Keurig K55 Manual Keurig K55 Manual](/uploads/1/2/4/7/124769377/845688315.jpg)
This water filter kit will help you enjoy better-tasting Keurig coffee - Two water filters and instructions are included. Compatible with: Keurig K50, K55, K60. Can I run hot water through the Keurig 55? The current 2.0 does not allow us to do it but our older model.
Background and IdentificationThe Keurig K55 is a single serving coffee brewer from Keurig and is a member of Keurig's Classic Series. Released in 2015, the K55 holds 48 ounces of water and supports brew sizes of 6, 8, and 10 ounces. Further, the K55 boasts a brew time of under one minute and an auto shut-down feature. Additionally, the K55 supports Keurig's My K-Cups, allowing you to brew your own grounds with your Keurig.The K55 is no longer sold by Keurig and has been replaced by the K50 line.Though very similar to the K50, the K55 is slightly shorter at a height of 13 inches versus the 13.3 inch tall K50. Further, the K55 is heavier than the K50, weighing 12 pounds versus the K50's 7 pounds.
Save Time and Money with These Keurig K-Cup Brewer SolutionsHaving problems with your Keurig K-Cup Brewer? Repeated usage can cause functional issues, which will impact the brew quality of your and ultimately your coffee drinking experience. The good news is there are a number of ways to fix these problems and get your machine to function as good as new. Here are five common and easy ways to correct these problems.
Common Problem 1: K-Cup Coffee and Tea Grounds Get into Your K-Cup Holder and Causes a Water Line ClogKeurig Troubleshooting Solution: Remove or clean the needle that punctures the K-Cup Pod then do a small cup cleansing brew to clean out any residual. This will ensure any left-over debris is flushed out before you have you start your next brew. Common Problem 2: K-Cup Brewer Shuts Off Unexpectedly Between BrewsKeurig Troubleshooting Solution: Remove the water reservoir and insert it back into place. The magnet in the reservoir can become dislodged during brewing from the vibrations in the machine.Common Problem 3: Not Ready Message on Your Keurig Machine Stays OnKeurig Troubleshooting Solution:.
Turn off your machine and unplug it. Detach the water reservoir. Wait 5 seconds then repeat the steps 1 and 2. Insert the water reservoir then press the menu button and when the “Not Ready” message appears lower handleCommon Problem 4: Blinking Blue Light in Water ReservoirKeurig Troubleshooting Solution: Simply add more water to the reservoir. All models need a minimum amount of water to activate the brewing process, so if you’re reservoir is low the machine will not start.
Common Problem 5: Installing Your Water FilterKeurig Troubleshooting Solution: This problem applies to only the models with the water filter feature. If you own one of these models, you can install the filter in three simple steps:. Soak the entire filter in cold water for five seconds.
Place the filter at the bottom of the Water Handle Assembly. Set the timing dial two months from the day to ensure it is replaced at the appropriate timeUse these five Keurig troubleshooting solutions for your machine and you’ll ensure your coffee and tea always taste great and your brewer lasts a long time.
As a result, you’ll save yourself time and money not having to replace your Keurig K-Cup Brewer. What’s with getting a message that this pod is not correct for this coffeemaker when it’s the same one I’ve been using for two years? If you keep trying sometimes it finally works.
Ready to toss the thing and go back to the simple but dependable coffee makers of the past. Will not recommend buying one to anyone. Second time I’ve had a problemlast time I had company and had to go out and buy a Mr Coffee until a part arrived.
Frustrating when you’re half asleep and just want a cup of coffee. Incidentally did do the needle cleansing thing and it didn’t make much difference.